Microprocessor & Microcontroller Trainers and Interface Modules

Microprocessor Trainer

86/88-3:

16 bit 8086 based advanced Microprocessor Trainer with on-board DAC, RS-232-C port, 20×4 LCD, PC Keyboard connector, Windows / DOS driver and provision for ADC, RS 485, etc.

86/88-2:

16 bit 8086 based Microprocessor Trainer with on-board keypad, 8 digit seven segment display, RS-232-C and Windows / DOS driver.

86/88E:

16 bit 8086 based low cost Microprocessor Trainer with on-board RS-232-C port, USB port, 20X4 LCD, PC keyboard connector and Windows / DOS driver.

85 A:

8 bit 8085 based Advanced Microprocessor on-board EPROM Programmer, Keypad, seven segment display, printer port, RS-232-C port, USB port, built-in Editor, Assembler and Disassembler.

MPS 85-3:

8 bit 8085 based Microprocessor Trainer with on-board keypad, seven segment display, RS-232-C, battery backup for RAM, Windows / DOS driver, built-in Editor, Assembler and Disassembler Trainer

Microcontroller Trainer

REV 51:

8 bit 8051 based advanced Microcontroller Trainer with on-board DAC, RS-232-C port, 20X4 LCD, PC keyboard connector, Windows / DOS driver and provision for ADC, RS 485, etc.

REV31:

8 bit 8051 based Microcontroller Trainer with on-board keypad, 7 digit seven segment display, printer port, Rs-232-C port and Windows / DOS driver.

REV51E:

8 bit 8051 based low cost Microcontroller Trainer with on-board RS-232-C port, USB port, 20X4 LCD, PC keyboard connector and Windows / DOS driver.

REVMCB51:

Single Chip MCU Trainer Based on 89C51Rx2 and supports on-board programming & Integrates with Keil IDE µVision3

PIC Trainer

REV PIC 01:

PIC 16F876 based Microcontroller Trainer with on-board RS-232-C, provision to debug, programming via RJ11 cable using ICD 01.

REV PIC 02:

PIC 16F876 based Microcontroller Trainer with on-board RS-232-C, 16X2 LCD, 4 digit seven segment display, I2C, Relay and provision to debug, programming via RJ11 cable using ICD 01.

REV PIC 03:

PIC 16F877 based Microcontroller Trainer with on-board RS-232-C,6 digit seven segment display, 10 bit ADC, provision to debug,programming via RJ11 cable using ICD 01. Compatible with common GSAS Interface Modules.

In-Circuit Debugger

NAX ICD 01:

In-circuit debugger and In-circuit Serial programmer for PIC 01, 02 &03 Trainers using MPLAB IDE.

Interfacing Modules

IF -8251/8253*:

8251/8253 Study Card Interface.

IF – 8255*:

8255 Study Card Interface.

IF – 8259*:

8259 Study Card Interface.

IF – 8279*:

8279 Study Card Interface.

IF -8ADC 12M:

12 bit ADC Interface with 8 Channel MUX 10 µsec, using AD1674.

IF – 16 ADC 8:

16 Channel 8-bit ADC Interface using ADC0816.

IF-DADC:

DAC for ADC & Temp.Sensor Interface.

IF -DDAC:

Dual DAC Interface.

IF -DIS:

4 – Digit, Seven Segment LED Display Interface.

IF – DSADC:

Dual Slope ADC Interface.

IF- ELV:

Elevator Interface.

IF – KBD:

Calculator Type Keyboard Interface.

IF – HEX KPD:

4X4 Matrix Hex Keypad Interface.

IF – LC:

Logic Controller Interface.

IF – LCD:

16X2 LCD Interface with backlit.

IF – MTG:

Musical Tone Generator Interface.

IF – µP24*:

24 Column Dot Matrix Printer Interface with Epson M180 Printer Mechanism.

IF – OPTIN:

Opto Isolated Input Interface.

IF – OPTOUT:

Opto Isolated Output Interface.

IF – PGMR*:

EPROM Programmer Interface (2716 through 27512).

IF – RLYO:

Relay Output Interface.

IF – RTC:

Real Time Clock Interface (with battery backup).

IF – STEP:

Stepper Motor Interface with Stepper Motor (3Kg/cm, 5V DC) & Power Adapter.

IF – TRL:

Traffic Lights Interface.

IF – TXDR ADC:

TXDR Interface using ICL7109A and RTD, PTI00 with 2 wire configuration.

IF – DC MOTOR:

DC Motor Interface with DC Motor and RPM sensor.

IF – KBD – DISP:

4X5 Matrix Calculator style keyboard and 6 Digit, 7 Segment Display Interface.

Contact Revine Technologies for Data Sheets